Dual energy X-ray absorptiometry

(Redirected from DXA)
Jump to navigation Jump to search

Dual energy X-ray absorptiometry (DXA, previously DEXA) is a means of measuring bone mineral density (BMD). Two X-ray beams with differing energy levels are aimed at the patient's bones. When soft tissue absorption is subtracted out, the BMD can be determined from the absorption of each beam by bone. DXA is the most widely used and most thoroughly studied bone density measurement technology. A T-score of -2.5 or less is indicative of osteoporosis.

DXA scans can also be used to measure total body fat content, which is useful for athletes, models and health-conscious people.

Special considerations are involved in the use of DXA to assess bone mass in children. Specifically, comparing the bone mineral density of children to the reference data of adults (to calculate a T-score) will underestimate the BMD of children, because children have less bone mass than fully developed adults. This would lead to an overdiagnosis of osteopenia for children. To avoid an overestimation of bone mineral deficits, BMD scores are commonly compared to reference data for the same gender and age (by calculating a Z-score).

Also, there are other variables in addition to age which are suggested to confound the interpretation of BMD as measured by DXA. One important confounding variable is bone size. DXA has been shown to overestimate the bone mineral density of taller subjects and underestimate the bone mineral density of smaller subjects. This error is due to the way in which DXA calculates BMD. In DXA, bone mineral content (measured as the attenuation of the X-ray by the bones being scanned) is divided by the area (also measured by the machine) of the site being scanned.

Because DXA calculates BMD using area (aBMD: areal Bone Mineral Density), it is not an accurate measurement of true bone mineral density, which is mass divided by a volume. In order to distinguish DXA BMD from volumetric bone-mineral density, researchers sometimes refer to DXA BMD as an areal bone mineral density (aBMD). The confounding effect of differences in bone size is due to the missing depth value in the calculation of bone mineral density. It should be noted that despite DXA technology's problems with estimating volume, it is still a fairly accurate measure of bone mineral content. Methods to correct for this shortcoming include the calculation of a volume which is approximated from the projected area measure by DXA. DXA BMD results adjusted in this manner, are referred to as the bone mineral apparent density (BMAD) and are a ratio of the bone mineral content versus a cuboidal estimation of the volume of bone. Like aBMD, BMAD results do not accurately represent true bone mineral density, since they use approximations of the bone's volume. Other imaging technologies such as Computed Quantitative Computer Tomography (QCT) (see pQCT Peripheral quantitative computed tomography) are capable of measuring the bone's volume, and are therefore not susceptible to the confounding effect of bone-size in the way that DXA results are susceptible.

BMAD is used primarily for research purposes and is not used in clinical settings, yet.

DXA uses X-rays to assess bone mineral density. However, the radiation dose is approximately 1/10th that of a standard chest X-ray.[1]

The quality of DXA operators varies widely. DXA is not regulated like other radiation based imaging techniques because of its low dosage. Each state has a different policy as to what certifications are needed to operate a DXA machine. California for example requires coursework and a state-run test, whereas Maryland has no requirements for DXA technicians. Many states require a training course and certificate from the International Society of Clinical Densitometry (ISCD). Because BMD testing with DXA is very susceptible to operator error (it is not fool-proof) it is important to find out what qualifies the technician to operate the machine.

It is important for patients to get repeat BMD measurements done on the same machine each time, or at least a machine from the same manufacturer. Error between machines, or trying to convert measurements from one manufacturer's standard to another can introduce errors large enough to wipe out the sensitivity of the measurements.


External links

he:בדיקת צפיפות עצם